Brand name: Happymodel
Item name: SE0802 1-2S brushless motor
KV: 16000KV, 19000KV (option)
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Terminals: JST1.25mm
No.of Cells(Lipo): 1-2S
Wire length(include connector): 40mm
Weight: 1.9g
Features:
Super tiny only 1.9g
Double E-clip design, prevent Motor bell to flying off
Good Dynamic balance
Happymodel
Please note: Our stock is already fitted with Happymodel 1102 9000KV brushless motors (no throttle adjustment required) and come with the latest V3 frame. Capacitors are also included to avoid voltage spike and can be fitted if requested (Rubycon ZLH 100uf 16v/220uf 16v).
Specifications:
Brand Name: Happymodel
Item Name: Mobula7 HD 2-3S 75mm Brushless whoop drone
Wheelbase: 75mm
Size: 98mm*98mm*45mm
Weight: 48g(without battery)
Weight:72g(with Original 3s 300mah Lipo battery )
Features:
New Crazybee F4 PRO V2.0 AIO Flight controller 1-3s Lipo Compatible
2S for indoor Cine whoop mode
3S for outdoor Freestyle whoop mode
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
The lightest 1102 brushless motor only 2.7g with double ball bearings
Powerful and smoothly
Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output)
Caddx turtle v2 + 1080p 60fps DVR ready
Camera Angle adjustable
VTX power switchable 25mw~200mw
Smartaudio ready , change VTX bands, powers, channels via OSD
Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
Flysky version support both AFHDS and AFHDS-2A protocol transmitter
DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc..
Full telemetry function ready (Frsky Non-EU and Flysky version support)
Special Breath light ready
Real Bind and Fly version
Compatible both for 2s-3s Lipo/LIHV
Package includes:
Item Name | Qty |
Mobula7 V3 Frame | 1 |
Option1: Crazybee F4FR V2.0 PRO FC built-in Frsky NON-EU RX | 1 |
Option2: Crazybee F4FS V2.0 PRO FC built-in Flysky RX | |
Option3: Crazybee F4DX PRO FC built-in Serial-bus DSM2/DSMX RX | |
Option4: Crazybee F4 V2.0 PRO FC no RX verion | |
EX1102 KV9000 Motor | 4 |
40mm black propellers (2cw+2ccw) | 1 |
Caddx Turtle v2+1080p 60fps DVR | 1 |
5.8G 40ch 25mw-200mw VTX | 1 |
3S 11.4v 300mah 30C/60C battery | 1 |
Propeller disassemble tool | 1 |
Screwdriver | 1 |
Spare parts specifications:
Motor | >Mode: EX1102 KV9000 Configu-ration:9N12P Stator Diamter:11mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ13.5mm*16mm Weight(g):2.8g No.of Cells(Lipo):1S-3S |
Flight controller | (Frsky version) CRAZYBEE F4FR PRO V2.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V2.0 Firmware target: CrazybeeF4FS (DSM2/DSMX version) CRAZYBEE F4DX PRO V2.0 Firmware target: CrazybeeF4DX (No RX version) CRAZYBEE F4 PRO V2.0 Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-3S battery input (DC 3.5-13V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) DSM2/X Version built-in Serial-based DSM2/DSMX compatible satellite receiver No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1-3S LiPo/LiPo HV (3.5v/13v) Current: 5A continuous peak 6A (5 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 |
Frsky NON-EU receiver Version | SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
Flysky receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
DSM2/DSMX receiver version | Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
PNP No RX version | No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc. |
VTX | Output power: 25~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With RacebandSmartaudio ready Weight: 3g |
CADDX Turtle V2 | Image sensor: 1/2.7″ CMOS sensor Horizontal: 800TVL TV system: NTSC/PAL changeable Video Resolution: 1080P@60fps / 1080P@30fps / 720@60fps Power Input: DC 4.5-20V FPV FOV: 155° Recording FOV: 170° Mini Illumination: 0.01lux Image Resolution: 2 Megapixels Lens: 1.8mm Turbo Eye Lens Working Current: 380mA@5V/160mA@12V (low consumption) OSD Menu: Yes (Support Voltage Display) Video Files: MP4 Audio: Support Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100 S/N Ratio: >60dB (AGC OFF) Video Output: CVBS Max Micro SD Card Supported: 8-64GB(need Class 10 or above, recommend Class 10/UHS-I/UHS-II) Color: Red |
Lipo Battery | Capacity:300mAh Voltage:11.4v Continuous Discharge Rate: 30C Instantaneous discharge rate: 60C Size: 65mmx18mmx11mm Weight: 23g Connector: XT30 |
Manuals:
- Download Mobula7 HD Frsky Manual
- Download Mobula7 HD Flysky Manual
- Download Mobula7 HD DSMX Manual
- Download Mobula7 HD PNP Manual
Specifications:
Brand Name: Happymodel
Mode Name: Mobula7
Item Name: 2S 75mm Brushless Whoop racer drone BNF
Wheelbase: 75mm
Size: 98mm*98mm*36mm
Weight: 27g(without battery)
Take off Weight:40g(with Original 250mah lipo battery x2 )
Features:
New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
2S whoop more powerful and more flight time
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output)
Smartaudio ready , change VTX bands, channels via OSD
Adjust the settings and the PID of the flight controller via OSD
Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
Flysky version support both AFHDS and AFHDS-2A protocol transmitter
DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
Frsky EU-LBT version support Frsky EU-LBT firmware transmitter
Full telemetry function ready
Head lights ready
Camera angle adjustable
Real Bind and Fly version
Buzzer Ready
Package includes:
Item Name | Basic version | Standard version |
75mm Brushless Bwhoop75 Frame | 1 | 1 |
Option1: Crazybee F3 PRO FC built-in Frsky NON-EU receiver | 1 | 1 |
Option2: Crazybee F3 PRO FC built-in Flysky receiver | ||
Option3: Crazybee F3 PRO FC built-in DSM2/DSMX receiver | ||
Option4: Crazybee F3 PRO FC built-in External Frsky XM+ receiver | ||
SE0802 KV16000 Motor | 4 | 4 |
40mm propeller(4cw+4ccw) | 1 | 1 |
AIO Camera & VTX | 1 | 1 |
Buzzer | 1 | 1 |
3.8v 250mah 30C/60C battery | 4 | 4 |
USB Lipo/LIHV Charger | 1 | 0 |
1S06 6 way Lipo/LIHV charger | 0 | 1 |
Propeller disassemble tool | 1 | 1 |
Screwdriver | 1 | 1 |
*Notes: Standard version not include Power Adapter
*DSM2/DSMX and Frsky EU-LBT version are Serial-based receiver, so Smartaudio is not compatible
Spare parts specifications:
Motor | Mode: SE0802 KV16000 Configuration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.5mm Weight(g):1.8g No.of Cells(Lipo):1S-2S |
Flight controller | (Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR (Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS (DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX (Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS MCU: STM32F303CCT6 (72MHZ, 256K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 3.5-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) DSM2/X Version built-in Serial-based DSM2/DSMX compatible satellite receiver Frsky EU-LBT version Built-in External XM+ receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection BLHELI_S pass-through Ready Heading LED Ready |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v) Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_L_5_REV16_7.HEX Default protocol: DSHOT600 |
Frsky NON-EU receiver Version | SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
Flysky receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
DSM2/DSMX receiver version | Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
Frsky EU-LBT Version( External XM+ receiver) | Operating Voltage Range: 3.7~10V Operating Current: 30mA @5V Operating Range: Full range With RSSI output on board: Analog 0~3.3V Firmware Upgradeable, Default firmware EU-LBT with RSSI |
AIO Camera&VTX | Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Camera resolution: 700TVL Field of view: 120° Video Format: NTSC Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With RacebandSmartaudio ready(Frsky EU-LBT and DSMX version not compatible) Size: 13.9″12.0mm ( L*W ) Weight: 3g |
Lipo Battery | Capacity:250mAh Voltage:3.8v Continuous Discharge Rate: 30C Instantaneous discharge rate: 60C Size: 55mmx12mmx7mm Weight: 6.5gConnector: PH2.0*Notes: Need 2pcs batteries for Series circuit |
Happymodel Mobula7 Part 40mm 1.0mm Hole 4-Blade Propeller 2 CW & 2 CCW for 0603 0703 0802 Motor – Black/Blue/Green/Red
Length:40mm
Shaft hole:1.0mm
Suitable for:8520 Brushed,0603(1mm shaft) 0703 0802
Package include:
2cw propellers + 2ccw propellers
Happymodel Mobula7/HD V3 Frame - Smoke Black/Transparent
New design, more durable than V2 , with Mobula7 Led_strip mount hole
The smoke black color v3 frame is original for Mobula7 HD
Specifications:
Wheelbase:75mm
Weight:5.5g
could fit the bellowing batteries:
Happymodel 2S 300mah
Happymodel 3s 300mah
GNB 2S 300mah
GNB 3S 300mah
Compatible for Happymodel 0603/0703/0802/EX1102 seires brushless motors
Mobula7 improvement frame , new materials, more durable, more light
Specifications:
Wheelbase:75mm
Weight:4.2g
Color option: Transparent or Transparent Black
Model: M7FRAME V2
RECOMMENDED PARTS:
Propellers: 40mm 3blades or 4blades
Motors: Happymodel 0603/0703/0802 Brushless motor
Flight controller : Crazybee F3 , Beecore BL , Beecore omnibus Crazybee F3 PRO. Crazybee F4 PRO
Battery: 1S Lipo Lihv 450mah or 550mah or 2S 250mah/300mah
Capacity: 250mAh
Voltage: 3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 55mm x 12mm x 7mm
Weight: 6.5g
Connector: PH2.0
Please note that orders containing batteries will be sent as 'Road Transport Only' and cannot be sent by Express Post.
Capacity: 300mAh
Voltage: 3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 57mm x 12mm x 7mm
Weight: 6.5g
Connector: PH2.0
Please note that orders containing batteries will be sent as 'Road Transport Only' and cannot be sent by Express Post.
Brand Name: Happymodel
Capacity: 300mAh
Voltage: 11.4v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 65mm x 18mm x 11mm
Weight: 24g
Connector: XT30
Please note that orders containing batteries will be sent as 'Road Transport Only' and cannot be sent by Express Post.
Crazybee F4 Pro V2.0 1-3S compatible flight controller for Mobula7/HD
Notes:
The biggest differences between Crazybee F4 PRO V1.0 and V2.0 are:
V2.0 could handle 1-3s Lipo/LiHV
V1.0 could handle only 1-2s Lipo/LiHV
V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”
Flight controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-3S battery input (DC 3.5-13V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready ESC MCU Upgraded to EFM8BB21 Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS-2A Compatible) DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver) No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc. Built-in Betaflight OSD (SPI Control) Built-in Current meter sensor Max up to 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection BLHELI_S pass-through Ready Multi Serial port support Fully compatible with almost Brushless whoop drone Weight:4.3g |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1-3S LiPo/LiPo HV (3.5v/13v) Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 |
Receiver support | No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc. |
Firmware target:
Frsky version betaflight_4.0.0_CRAZYBEEF4FR.hex
Flysky version betaflight_4.0.0_CRAZYBEEF4FS.hex
DSM2/DSMX version betaflight_4.0.0_CRAZYBEEF4DX.hex
No RX version betaflight_4.0.0_CRAZYBEEF4DX.hex
Package include:
1 x CrazybeeF4 PRO flight controller
3 x Power cables
1 set Shock absorbing rubber and screws
Specifiactions:
Mode: EX1102
KV options: 9000KV 10000KV 13500KV
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ13.5mm*16mm
Weight(g):2.8g
No.of Cells(Lipo):2S-3S
Features:
The lightest 1102 brushless motor all over the world
Mobula7 HD original brushless motors
Dual bearing design and more balance
40mm – 66mm propellers compatible
Could use for 2s-3s 75mm-85mm whoops and best for 66mm ductless frame
Item Name: Camera Canopy for Mobula7
Material: PC
Color option: Transparent Red
Net Weight: 2g
Camera angle could adjustable easily
Best for CADDX EOS2 camera
Package Included:
1 x Camera Canopy set
2 x M1.2*5 Screws (Mount the plastic)
2 x M2*5 Nylon Screws(Mount the EOS2 camera)
*Notes: The M2*5 Nylon Screw should cut to M2*3 in order to fit the EOS2 Cam , or you can buy M2*3 metal screws
Canopy for Caddx Turtle2 Mobula7 HD original Canopy
Description:
Brand Name: Happymodel
Item Name: Turtle2 Camera Canopy for Mobula7 HD
Material: PP
Color: Smoke Black
Net Weight: 2.9g
Camera angle could adjustable easily
Package Included:
1pcs Camera Canopy
5pcs Screws
2pcs M2x5x1 Nylon gasket
Length 5.5cm
Includes: 1 x cable for Caddx Turtle V2
Small size, lighter and easy to mount in a regular whoop
Best for the Mobula7 upgraded
Output power: 25~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Antenna: RG178 antenna U.FL interface
Frequency: 5.8GHz 5 bands 40 channels
Smartaudio ready
Weight: 2g without antenna