Stack / FC / ESC
Crazybee F4 Pro V2.0 1-3S compatible flight controller for Mobula7/HD
Notes:
The biggest differences between Crazybee F4 PRO V1.0 and V2.0 are:
V2.0 could handle 1-3s Lipo/LiHV
V1.0 could handle only 1-2s Lipo/LiHV
V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”
Flight controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-3S battery input (DC 3.5-13V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready ESC MCU Upgraded to EFM8BB21 Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS-2A Compatible) DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver) No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc. Built-in Betaflight OSD (SPI Control) Built-in Current meter sensor Max up to 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection BLHELI_S pass-through Ready Multi Serial port support Fully compatible with almost Brushless whoop drone Weight:4.3g |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1-3S LiPo/LiPo HV (3.5v/13v) Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 |
Receiver support | No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc. |
Firmware target:
Frsky version betaflight_4.0.0_CRAZYBEEF4FR.hex
Flysky version betaflight_4.0.0_CRAZYBEEF4FS.hex
DSM2/DSMX version betaflight_4.0.0_CRAZYBEEF4DX.hex
No RX version betaflight_4.0.0_CRAZYBEEF4DX.hex
Package include:
1 x CrazybeeF4 PRO flight controller
3 x Power cables
1 set Shock absorbing rubber and screws
Mamba F405 Mini FC

Mamba interference shielding FPC Instructions:
1. Get as close to the FC board as possible
2. Maintain ESC Cool Airflow
3. Do not damage the FPC surface coating
4. Only connecting 1 GND from FC is ok
Package includes:
20mm*1 Shield
30.5mm*1 Shield
(Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS (No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 7-17V) Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Current meter scale set to 470 Built-in 5V 1A BEC Built-in voltage detection |
MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 10A continuous peak 12A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_5.HEX Default protocol: DSHOT600 |
SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
No RX version support external serial-bus receiver like XM+, crossfire, S-FHSS etc. |
Recommend Battery: 2S 450mah/550mah , 3S 300mah/350mah/450mah, 4S 300mah/350mah
Notes: If used 3inch propellers, we recommend use 2-3S only
Note:Because the STM32F722 can get hot, please leave at least 5mm space at both sides of the FC with nothing covered to make sure it gets good air circulation.
FC Specifications
MCU: 216MHz STM32F722RET6 32BIT
IMU: MPU6000
Baro: No
OSD: BF OSD
Blacbox: 16M Flash Memory
Uarts: 6Set
ESC Soft: Dshot300/600/1200
ESC Telemetry: RX2
LED: Blue&Orange for FC Status,,White 5V,Red 3.3V
WS2812 LED Control: BF LED Control
Smartaudio: Yes
RSSI: Yes
Buzz: Yes
Input: 2~6S Lipo (8.4~25V)
VTS Protection: Yes
BEC: 5V 2A (Max 3A)
ESC Specifications
INPUT VOLTAGE: 2~6S Lipo (7.4V~25V)
CONTINUE CURRENT: 30A×4
BURST CURRENT: 35A (10S)
BEC: NO SOFT: Dshot300/600/1200
MOUNTING: 20mm/M2
Supply : Panasonic High Frequency 470uF/35V
Mounting: 20×20mm,Φ2
Dimensions: 30×36.5×13.5mm
Weight: 11g
Including
1×FC MAMBA F722MINI Stack
PRODUCT DESCRIPTION
SucceX Micro F4 Flight Tower System 16x16mm
Specification:
SucceX F4 Flight Controller
-STM32F411
-Input voltage 2-4S LIPO
-Gyro: MPU6000
-2x UART ports
-4x motor outputs
-OSD inbuilt
-No Blackbox FLASH
-BEC 5V 2A cont.
-Size: 21mm*21mm
-Mounting holes: 16*16
-Weight: 2.5g
-BF target : MATEKF411
SucceX Micro 12A Brushless ESC
-Firmware: BlheliS
-Input voltage : 2-4S LIPO
-Continuous current: 12A
-MCU: BB21F16G
-BEC : None
-ESC protocol: pwm, oneshot125, multishot, dshot150, 300, 600, etc.
-Size: 23mm*21mm
-Mounting hole 16*16mm
-Weight: 2.7g
SucceX Micro VTX
-Power : PIT/25/100/200mW
-Antenna interface : IPEX (UFL)
-Telemetry: IRC Tramp
-Size: 17mm*27mm
-Mounting holes: 16*16mm
-Weight: 1.6g
Package Included:
1 x SucceX F4 Flight controller
1 x 12A Brushless ESC
1 x PIT/25/100/200mW VTX
PRODUCT DESCRIPTION
SucceX F4 Flight Controller (V1.5)
-STM32F411
-Input voltage 2-4S LIPO
-Gyro: MPU6000
-2x UART ports
-4x motor outputs
-Betaflight OSD :YES
-Blackbox FLASH: 8MB
-BEC 5V 2.5A cont.
-Size: 21mm*21mm
-Mounting holes distance: 16*16mm
-Weight: 2.5g
-Firmware : betaflight_4.0.5_STM32F411.hex
-CLI dump file: IFF411_PRO.config
SucceX Micro 12A 4-in-1 ESC(w/plug)
-Firmware: G-H-30 BLS 16.7
-BLHeliSuite: http://www.mediafire.com/file/1tn449x6815upat/BLHeliSuite16714901.zip/file
-Input voltage : 2-4S LIPO
-Continuous current: 12A
-MCU: BB21F16G
-BEC: NO
-ESC protocol: pwm, oneshot125, multishot, dshot150, 300, 600, etc.
-Size: 23mm*21mm
-Mounting hole 16*16mm
-Weight: 2.7g
5.8G 200mW Micro VTX
-Power: PIT/25/100/200mW
-Antenna interface: IPEX (UFL)
-VTX protocol : IRC Tramp
-Size: 17mm*27mm
-Mounting holes: 16*16mm
-Weight: 1.6g
Downloads:
*SucceX Micro,Whoop)IFLIGHT_F411_PRO.config
*SucceX Micro 16x16,SucceX Whoop FC Firmware(beta flight 3.5.7)
*SucceX Micro 16x16,SucceX Whoop FC Firmware(beta flight 4.0.4)
Package Included:
1 x SucceX Micro F4 Flight controller (M3 hole)
1 x SucceX Micro 12A Brushless ESC (M3 hole)
1 x PIT/25/100/200mW VTX (M3 hole)
Replacement parts:
Replacement 200mw VTX
NOTE: ESC V1.5 is compatible with V1.3
Specification
Brand Name: Diatone Mamba
Model: MAMBA F411AIO Dshot600 4S
MAMBA F411AIO
-STM32F411
-Input voltage 2-4S Lipo
-Gyro: MPU6000
-2x UART ports
-OSD inbuilt
-BEC 5V 1.5 A
-Size:28.5*28.5mm
-Mounting holes: 25.5*25.5mm M2
-Weight: 6.1g
-BF target: Mamba F411
-Input voltage : 2-4S LIPO
CONTINUE CURRENT: 13A×4
BURST CURRENT: 15A (10S)
-ESC protocol: pwm, oneshot125, multishot, dshot150, 300, 600, etc.
Package Included:
MAMBA F411AIO Dshot600 4S *1
HGLRC Forward FD445 Stack FC&45A4in1 20x20mm BLHeli_32 2-6S
Specification: (User Manual)
Model: Forward FD445 Stack
Usage: for 110mm-1000mm Frame Kit
1.Forward F4 MINIFlight Control 、
CPU: STM32F405R6T6
MPU: MPU6000-SPI
Input Voltage: 2-6S Lipo
Firmware: Betaflight OMNIBUSF4V6
Built-in Betaflight OSD to adjust PID
BEC Output: 5V@3A
Size: 25.0x25.0mm board
Installing Hole:20x20mm,M2
Weight:4.7g
2. Forward 45A 4in1 MINI ESC
CPU:STM32F051
Input Voltage: 2-6S Lipo battery
Constant Current: 45A-4S/35A-6S
Peak Current: 55A(5s)
BEC Ouput: NO
Firmware: BLHELI_32
Size: 31.7x36.5mm
Installing Hole:20x20mm,M2
Weight: 10.8g
Package Included:
1x Forward F4 MINI Flight Control
1x Forward 45A 4in1 MINI ESC
1x Cable Set
HGLRC XJB F428-TX20.V2 Omnibus F4 Flight Controller 28A 2-4S Blheli_S ESC 25/100/200/350mW VTX for RC Drone
The voltage requests to be 3.5V above when you use 2S Lipo for F428 stack.
Specification: (User Manual)
Model: HGLRC XJB F428-TX20.V2
Weight: 8.9g
Usage: for 65mm-250mm Frame Kit
Upgrade Micro F4.V2 Flight Control Board ( D-Shot Version)
MPU: MPU6000-SPI
CPU: STM32F405RGT6, dual 8K.
Black Box: Flash 16M
Input Voltage: 2-4S Lipo
Built-in Betaflight OSD to adjust PID
BEC Output: 5V@3A
Size: 25x25mm board, 20mm mounting holes (M2)
Weight:2.3g
Support SBUS/PPM/DSMX receiver
28A 2-4S Blheli_S BB2 4 in 1 ESC:
Input Voltage: 2-4S Lipo battery
Constant Current: 28A
Peak Current: 35A
BEC Ouput: NO
Firmware: BLheli_S 16.5
Size: 27x27mm (main board)
32x32mm ( including pad)
Installing Hole: 20x20mm, M2
Weight: 4.2g
CPU: SILABS EFM8BB2 48MHZ
MOS Tube: TOP QUALITY MOSFET
Firmware: Betaflight 16.5
Support Damped Mode, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, forward and reverse
HGLRC XJB-TX20.V2 Mini FPV Transmitter
Output power: PIT/25mW/100mW/200mW/350mW switchable
Control mode:BFOSD control(RX)/button
BAT: 7-26V,BEC 5V-1A
240mA----350mW
Video system: NTSC/PAL
Antenna: IPEX
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362-5945 MHZ
Size: 24*24mm(L*W),Hole:20*20mm
Weight: 2.4g
Package Included:
1x HGLRC F4.V2 AIO OSD BEC Flight Control Board
1x HGLRC 28A Blheli_S 4 In 1 ESC
1x HGLRC XJB-TX20.V2 Mini FPV Transmitter